BEST DATA PRODUCTS, INC.

SMART ONE 56SP, 56VF

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
I/O Options                  Audio line in, microphone in, speaker out,
                             voice, speakerphone
Maximum Data Rate            56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell K56flex
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10EC, V.42, V.42bis
Fax Class                    Class I
Data Bus                     16-bit ISA
Card Size                    Full height, half length

[Image]

                                CONNECTIONS

         Function            Label            Function              Label

  Telephone line out         CN1     Music-on-hold line in          CN4

  Telephone line in          CN2     Microphone in                  CN5

  Speaker out                CN3

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, ‘comma’, A/

  A, B, D, E, H, L, M, N, O, Q, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

                           Extended AT Commands

  \A, \B, \K, \N, \V

  %C, %E, %L, %Q

                            Special AT Commands

  #CID, :E, -K, @M

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S22, S24, S25, S26, S27

  S29, S30, S31, S32, S33, S36, S38, S46, S48, S82, S86, S91, S92, S95

            Note: See MHI help file for complete information.

  UNIDENTIFIED COMMANDS

   Command      Default

     S21          52

     S23          62

     S28           0

     S37           0

     S40          104

     S41          195

                         Proprietary AT Command Set

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware revision, model, and interface type.

       I4        Displays model number.

       I5        Displays country code.

       I6        Displays data pump model and version.

       I7        Displays DAA code.

                             DISTINCTIVE RING

  Format:             AT [cmds] -SDR=n [cmds]

  Default:            Unidentified

  Range:              0 - 7

  Description:        Selects which distinctive ring signals the modem
                      will respond to.

     Bit        Value                        Function

      0              0   Do not respond to distinctive ring type 1.

                    1    Respond to distinctive ring type 1.

      1              0   Do not respond to distinctive ring type 2.

                    1    Respond to distinctive ring type 2.

      2              0   Do not respond to distinctive ring type 3.

                    1    Respond to distinctive ring type 3.

                               MNP10EC MODE

  Type:                  Configuration

  Format:                AT [cmds] -SEC=n [cmds]

  Description:           Selects whether the modem will attempt to use
                         MNP10EC mode during the handshaking sequence.

        Command                              Function

         -SEC=0           MNP10EC handshaking disabled unless a V.34
                          connection is attempted via a cellular line.

         -SEC=1           MNP10EC handshaking enabled.

                              PROTOCOL/SPEED

  Type:             Configuration

  Format:           AT [cmds] Fn [cmds]

  Description:      Selects the protocol and speed the modem will attempt
                    to connect at.

     Command                              Function

        F0          Auto-detect the highest common connect speed.

        F1          Select V.21 or Bell 103 at 300bps speed.

        F3          Select V.23 at 75/1200bps speed.

        F4          Select V.22 or Bell 212A at 1200bps speed.

        F5          Select V.22bis at 2400bps speed.

        F6          Select V.32 or V.32bis at 4800bps speed.

        F7          Select V.32bis at 7200bps speed.

        F8          Select V.32bis or V.32 at 9600bps speed.

        F9          Select V.32bis at 12Kbps speed.

       F10          Select V.32bis at 14.4Kbps speed.